bcbloc02

Cummins Hyster doing BIG things!

Video | 1 months ago

Cummins Hyster Moving a BIG tree

Open this video on bcbloc02

Resurfacing aluminum DOHC 4 valve Chevy Hemi head

Video | 1 months ago

In this video I have a DOHC 4 valve Chevrolet Hemi Head that needs milled flat after a blown head gasket. It is a pretty straightforward job but the head is still assembled and has few squared machined surfaces. I thought the setup/workholding was interesti...

Open this video on bcbloc02

3204 Cat head

Guide | 2 months ago

3204/3208 Cat head rebuild, milling and drilling and valve job. In this vidoe I go thru a 3205 Cat head with a lot of wear and clean up all the surfaces, machine it for replaceable valve guides and install them and do a valve job. Sadly parts of this job we...

Open this video on bcbloc02

Piecing back together More Cast Iron with Welding

Video | 4 months ago

In this video I weld back together a couple of John Deere drawbar supports that were broken by a very heavy tongue weight manure spreader. A common job I do is tackle the unfixable and of course most say welding cast iron is one of those things so I do it a...

Open this video on bcbloc02

Cylinder Head Rebuild Using a Welder?

Video | 4 months ago

In this video I recondition and Allis Chalmers 301 Diesel head. It had seen a pretty rough life and had apparenly even got rain water down the exhaust for a while based on the corrosion of the center 2 cylinders. I also do wrist pin bushing replacement burn...

Open this video on bcbloc02

Fixing a Low Power and No start when Hot Condition on a P7100 Pump with Help from Area Diesel

Video | 6 months ago

In this video I have an Rv that was brought to me with the complaint of hard starting particularly when hot and low power, After doing some diagnosis work I determined the P7100 injection pump had issues. So I pulled it off and sent it to the experts at Are...

Open this video on bcbloc02

Modifying Dodge Dana 80 aftermarket hubs to fit a ford Dana 80.

Video | 6 months ago

In this video I had to bore a bearing pocket and the seal area to fit the correct sized parts for the particular axle these hubs were going on. When you get into one off parts modifications are often required. It is a straight forward boring job and was a p...

Open this video on bcbloc02

Deere 7400 MFWD Axle Pivot Repair Offset Align Boring to Restore Factory Alignment

Video | 7 months ago

In this video I bore and bush a John Deere 7400 MFWD axle pivot, Normally I do these assembled but this one had the pinion bearing messed up so it had to come apart anyway. Did some battle because of self inflicted stupidity but just made it take longer tha...

Open this video on bcbloc02

Fixing a semi Finished Chinese Bell and Gossett Pump. This one must have missed quality control.

Video | 9 months ago

In this video I go about making repairs on the electric motor on a circulating pump I bought for my shop hydronic system. This unit was bought with jnown issues but for the price i decided to take a shot on it. Follow along as I go thru what I found and how...

Open this video on bcbloc02

Just Another Head Job Valve job and resurfacing a Deere 466 Cylinder Head

Video | 9 months ago

In this video I fix up another almost 50 year old Deere Cylinder head. Keeping the vintage iron in the fields.

Open this video on bcbloc02

Resurfacing Duramax Cylinder Heads Smooth finish for MLS gaskets

Video | 11 months ago

In this video I resurfaced some duramax diesel gm cylinder heads. A real low feed rate with some wd40 did the milling followed by a flat stoning and some scotch brite to get it super smooth.

Open this video on bcbloc02

An oil change that saved an engine tear down?

Review | 1 years ago

In this video I talk about a misfire issue that developed with my 98 Dodge Dakota. I determined it seemed to be a lifter pumping up. Thanks to @themotoroilgeek I had seen this valvoline Restore and Protect being tested and it looked like it really cleaned e...

Open this video on bcbloc02