EP5 - Starting the engine
Guide | 2 months ago
In this video I get the engine started for the first time, paint the primer on the inside of the boat and repace the key ignition switch but a toggle switch and starter button. For outboard repair information, checkout my website: https://outboard.dangarmar...
Open this video on Dangar Marine
EP4 - Rotating the hull and engine
Guide | 6 months ago
In this video I turn the hull the right way up with the help of some friends, repair the paint and fibreglass a small hole in the hull. After that I start investigating the S195ND diesel engine to see if I can get it started using the crank handle. For outb...
Open this video on Dangar Marine
EP3 - Finishing the hull
Guide | 10 months ago
In this video Chabela and I finish the prep and painting of the outside of the hull of her old open putt-putt boat. For outboard repair information, checkout my website: https://outboard.dangarmarine.com/guide If you are enjoying this channel, please consid...
Open this video on Dangar Marine
EP2 - Preparing the hull for paint
Guide | 1 years ago
In this video I start sanding the old paint off the boat. The hull is quite textured so there any many low points where the old paint doesn't come off easily but I am hand sanding everything to make sure not of the paint is loose and flaky. For outboard rep...
Open this video on Dangar Marine
EP1 - New boat project - the Backstory
Guide | 1 years ago
In this video I introduce my new boat project, YTUQUÉ. It is open clinker boat that belongs to my neighbour Chabela and was partially restored by her late husband Mario. In this video we take a quick look at the boat and have a chat with Chabela to learn th...
Open this video on Dangar Marine
Diagnosing an outboard noise
Guide | 1 years ago
In this video Dave and I diagnose a noise coming from his 125HP Mercury 2-stroke outboard motor. It turns out to be missing teeth on the pinion and forward gears in the gearbox. For outboard repair information, checkout my website: https://outboard.dangarma...
Open this video on Dangar Marine
Finishing Renko's Deck
Guide | 1 years ago
In this video I chip away at some new rust that has formed since Renko was restored up in Bundaberg, apply some rust converter and then paint. Full video on cable and drum steering can be found here: https://www.youtube.com/watch?v=P3W-N2dd45U For outboard ...
Open this video on Dangar Marine
Helping a brother out
Guide | 1 years ago
In this video Adrian, Dave and I help Paul make a few repairs to his Yamaha 2-stroke outboard. The main job is to replace the trim tilt unit but we also replace the steering cable, service the water pump and replace the anodes. The boat has an problem with ...
Open this video on Dangar Marine
From Swamp to Swish!
Guide | 1 years ago
In this video I pull an old Savage fibreglass hull out of the mangroves and clean it up. I then mount a Yamaha 25HP outboard so I can use it as my new commuter boat on the river. For outboard repair information, checkout my website: https://outboard.dangarm...
Open this video on Dangar Marine
Back on the hard stand
Guide | 1 years ago
In this video I get Renko back up on the hard stand for a week to antifoul, paint the top sides, replace some of the anodes and attempt to get the stern gland out so I can fix it. I also take the opportunity to do an oil change, install a stern gland grease...
Open this video on Dangar Marine
Renko Rejuvenation
Guide | 1 years ago
In this video I begin to get Renko back into working condition after a year or so of neglect. For outboard repair information, checkout my website: https://outboard.dangarmarine.com/guide If you are enjoying this channel, please consider making a donation t...
Open this video on Dangar Marine
Halvorsen leak
Guide | 1 years ago
Temporarily stoping a leak in a Halvorsen from a worm hole. For outboard repair information, checkout my website: https://outboard.dangarmarine.com/guide If you are enjoying this channel, please consider making a donation to https://www.paypal.me/dangarstu ...
Open this video on Dangar Marine
