Ultra-Shear's NEW Deep Finger Grip Groove Bits cut deeper finger grips on your cutting boards.
Short | 1 months ago
A cutting board grip should feel like it belongs in the board. Ultra-Shear’s NEW Deep Finger Grip Groove Bit cuts a deeper, more natural-feeling parabolic grip in straight-edged or curved cutting boards. Use the included larger bearing for a subtler 3/16" g...
Open this video on Woodpeckers
The Right Balance of Bounce and Smack | Woodpeckers Polycarbonate Mallets
Short | 1 months ago
A good mallet needs the right balance of bounce and smack. Too soft, and the energy disappears. Too hard, and the work takes the punishment. Woodpeckers Polycarbonate Round Mallets pack solid striking power into a compact head, with a face that’s friendlier...
Open this video on Woodpeckers
Our Premium Router Table Packages are on sale this week! Save hundreds!
Short | 1 months ago
Save hundreds on a full-featured router table system. Woodpeckers Premium Router Table Packages bring the major parts of a serious router table workstation together in one configurable system – and they're on sale this week. Choose the table size, lift plat...
Open this video on Woodpeckers
Cut Tapers and Straight-Line Stock with More Control
Guide | 1 months ago
Woodpeckers Taper Sled gives you a controlled way to set up tapered cuts, secure the work, and guide the sled through the cut. Use it in the miter slot for typical taper work, or remove it from the miter bar and guide it with the rip fence for oversized tap...
Open this video on Woodpeckers
Four-Way Setup Blocks for Machine Adjustment
Short | 1 months ago
Setup blocks are most useful when they work more than one way. Woodpeckers 3D Setup Blocks give each common fractional dimension in four usable forms, plus built-in bevel angles for common machine setups. Use them to set and check blade heights, bit heights...
Open this video on Woodpeckers
Flatten Slabs and Oversized Glue-Ups with Woodpeckers Slab Flattening Mills
Guide | 1 months ago
Some slabs are too wide, too irregular, or too full of grain changes for traditional flattening tools. Woodpeckers Slab Flattening Mills give you a router-guided way to surface live-edge slabs, glued panels, tabletops, countertops, and workbenches in a cont...
Open this video on Woodpeckers
More Fence Support for Smaller Saws
Guide | 1 months ago
Smaller machines still need real fence support. Woodpeckers Compact Auxiliary Rip Fence clamps to compact table saws, band saws, and other fences under 3-1/4" tall, adding a 36" guide surface without permanently modifying the machine. The extra length and 7...
Open this video on Woodpeckers
Mortise Narrow Stock with Dual-Fence Router Support
Guide | 1 months ago
Mortising narrow stock is like a tight rope walk for a plunge router. Woodpeckers Mortise Base supports the router from both sides of the workpiece, using dual 2" fences to create a steadier setup for routing mortises. Adjust the fences to control the route...
Open this video on Woodpeckers
Alternating-Shear Bits for Cleaner Pattern Routing
Short | 1 months ago
Most shear-angle bits cut from one direction. Ultra-Shear 4-Flute Alternating-Shear Pattern & Flush Trim Bits take a different approach. Each successive flute alternates between up-cut and down-cut shear angles, slicing wood fibers from opposite directions ...
Open this video on Woodpeckers
Keep Your Assemblies Square While You Work with Woodpeckers Clamping Squares Plus
Short | 1 months ago
Panel assembly gets easier when the square and clamp work together. Woodpeckers Clamping Squares Plus help hold cabinet, case, box, and panel projects square from the inside or outside corner. The matching CSP Clamps lock directly into the square’s 3/8" hol...
Open this video on Woodpeckers
Accurate Cabinet Hardware Layout, New or Existing
Guide | 1 months ago
Cabinet hardware layout shouldn't rely on a keen eye and exacting alignment. Woodpeckers Shelf Pin and Drawer Slide Template gives you a precision-machined guide for accurate layout and drilling, whether you’re working on new cabinet parts or updating exist...
Open this video on Woodpeckers
Cleaner Crosscuts and Miters with Ultra-Shear Miter Saw Blades
Short | 1 months ago
Ultra-Shear Miter Saw Blades are built for clean crosscuts and miters on standard, sliding-compound, pivoting, and radial arm saws. The 80-tooth design uses four alternate-top-bevel teeth followed by a raker to slice fibers and clear shavings, while the neg...
Open this video on Woodpeckers
