15 recent indexed videos · 281,000 subscribers
Showing 12 of 15 kept videos
This video shows the usage of ClampMill DIY chainsaw mill starting from the first cut, no leveling needed. In 20 minutes I'm creating 6 edged boards that measure 140x25x2200mm. You can find ClampMill DIY here: https://naturetools.com/products/clampmill-diy-kit
I built the first prototype for ClampMill DIY already in September 2025 and we've been further developing it since then and now it is ready to finally launch. I'd be super happy if you find the time to check it out. Thank you!
This video shows the usage of ClampMill DIY chainsaw mill starting from the first cut, no leveling needed. In 20 minutes I'm creating 6 edged boards that measure 140x25x2200mm. You can find ClampMill DIY here: https://naturetools.com/products/clampmill-diy-...
Open this video on Donn DIYTurning heavier bar end weights in the lathe for Yamaha Tenere 700 Barkbusters hand guards.
Open this video on Donn DIYFabricating motorcycle manual tire changer from scratch start-to-finish. I'm using scrap metal pieces I have collected over the years. The only things I bought are the duck head and the drop center tools off of Aliexpress for around 40 bucks. I have wanted ...
Open this video on Donn DIYBuilding a 6x6 mini-forwarder out of my homemade 4x4 timber trailer with hydraulic crane. In this video I'm building the heating duct around the muffler that directs heat into the cab and fabricating oddly shaped hydraulic tank to max out the hydraulic oil ...
Open this video on Donn DIYBuilding a 6x6 mini-forwarder out of my homemade 4x4 timber trailer with hydraulic crane. In this video I'm making waterproof plywood floor, mounting the steering pump from an old Volvo and fabricating the hood / bonnet. Why build a forwarder? As a forest o...
Open this video on Donn DIYBuilding a 6x6 mini-forwarder out of my homemade 4x4 timber trailer with hydraulic crane. In this video I'm completing the chain tensioner mounting to the frame, mocking up plywood floors and installing the E-brake lever to the forwarder left wheel well. Wh...
Open this video on Donn DIYBuilding a 6x6 mini-forwarder out of my homemade 4x4 timber trailer with hydraulic crane. In this video I'm fabricating brake rotor and hub, brake caliper mount, truing up drive shaft and making jack shaft bearing blocks carrier. Why build a forwarder? As a...
Open this video on Donn DIYWinter is coming. In this video I'm fabricating a steel chimney for my workshop from scrap steel I had laying around. I did it super fast and without a foundation since I probably have to relocate it in the future. I used a bunch of field stones as anchor. ...
Open this video on Donn DIYFinishing milling live edge boards for the barn project with ClampMill chainsaw mill we invented at www.naturetools.com. I'm happy to say I'm part of this creation and that I built first two prototypes for ClampMill. I will keep this mill around next to my ...
Open this video on Donn DIYI'm starting to fix my old barn up so I'm sawmilling live edge boards with ClampMill from https://www.naturetools.com to replace siding on one end of the barn.
Open this video on Donn DIYTesting a Stihl MS 881 chainsaw. Cut speed comparison with Stihl MS 261C-M and bucking logs for firewood.
Open this video on Donn DIYBuilding a hydraulic log splitter from scratch. This is a summary video of the log splitter build series I did a while ago. It is still not painted and I use it "as is" because everything works well and I couldn't be happier with it as far as log splitters ...
Open this video on Donn DIY