Get the kits to complete these projects here: https://buildyourcnc.com/collections/arm-stm32-microcontroller-kits If you wish to support me and the efforts in making more content: https://buymeacoffee.com/patrickhooddaniel Get the companion book here: https://amzn.to/49Bv8QX
Join this channel to get access to perks: https://www.youtube.com/channel/UCC7ifdmN7ebFo-eXBUZkeiw/join
00:00:00 Introduction 00:04:36 Introduction to Bare Chip Microcontroller Development 00:07:40 The Prototyping Setup 00:11:23 Installing the new 2.0.0 STM32CubeIDE and supporting software (CubeMX and Cubemonitor) 00:22:43 IDE and Monitoring Software Setup (Legacy) 00:28:24 Getting Familiar with the STM32CubeIDE 00:31:12 Creating a Project in the IDE 00:34:47 Transferring the program to the microcontroller 00:37:40 Monitoring Runtime Data using STMStudio or STMCubeMonitor 00:42:34 Troubleshooting 1: Chip erase using the boot pin 00:44:06 Troublechooting 2: Chip erase using the reset pic 00:45:23 Troubleshooting 3: Power on AVCC not present 00:49:34 4 Most Important Code Instructions - Changing and testing bits 00:55:35 Project 1: Turning on an LED The "Hello World" of MCU Projects 01:14:38 Project 2: Receiving Input from a Button 01:30:31 Project 3: Latching an Input 01:44:30 Project 4: Interfacing an LCD Display 03:02:54 Using pointers to construct a string of characters 03:08:12 Project 5: Sending integers to the LCD 03:14:56 Project 6: Send floating point numbers to the LCD 03:20:09 Project 7: Set the location on the LCD 03:30:00 ADC (analog to digital conversion) introduction 03:40:09 Project 8: ADC Conversion (internal temperature sensor) 04:03:59 Project 9: Converting the ADC value to a meaningful number - Temperature - 04:12:28 Project 10: Potentiometer as the ADC input 04:19:48 Project 11: Timers and Counters Prescaler (Skip Oscillations) 04:29:54 Project 12: Timers and Counters: ARR (Auto reload register) Top Count Limit - Count Direction - Center Aligned Mode (Zig Zag Counting) 04:35:06 Introduction to PWM (Pulse width modulation) 04:42:43 Project 13: PWM (Pulse width modulation) 04:57:12 Project 14: Creating an ADC Header File 05:06:27 Project 15: Control PWM Output with the ADC 05:12:35 Project 16: Control the Dimming of an LED using PWM 05:14:09 Project 17: Control a Hobby Servo with the PWM Output 05:32:04 Project 18: Control a Hobby Servo with a potentiometer connected to the ADC 05:38:20 Introduction to Interrupts 05:44:50 Project 19: Using interrupts for ADC Conversion 05:58:43 Project 20: Using interrupts for ADC Conversion 2 Channels 06:08:45 Project 21: Fixing an Artifact on the LCD 06:14:03 Project 22: Push Button Interrupt 06:26:29 Project 23: External Interrupts on two pins 06:31:02 Project 24: Switch output to the STMStudio rather than the LCD 06:38:25 Introduction to the I2C or IIC communication protocol 06:50:33 Project 25: Communicating with the ADXL 345 Accelerometer via I2C - Writing 07:16:39 Project 26: Communicating with the ADXL 345 Accelerometer via I2C - Reading 07:25:58 Introduction to USART and other communication protocols 07:36:01 Project 27: Change the close speed to 48mhz 08:13:22 Project 28: Initialize the USART 08:57:32 Project 29: USART Receiving a Character 09:06:50 Project 30: USART Transmit to the Computer using CubeMX and HAL 09:22:45 Project 31: USART Receive and Transmit using Interrupts 09:38:34 Project 32: KiCAD Tutorial - Using the FTDI Application diagram to create a PCB 10:32:18 Project 33: Using ChatGPT to provide code to blink an LED 10:36:17 Project 34: Comparing two LLMs to write code for a simple I/O application
Get our Merch to support the channel: https://www.etsy.com/shop/BuildYourCNC